Dimplex VCX1525 Wartungshandbuch PDF herunterladen (Seite 8)

8 www.dimplex.com

Grasp the heater assembly and slide the heater as-11.

sembly and rear reective ame panel up, just enough

to reach inside and remove the black wire attached on

the right side of the dimmer control board. By remov-

ing this wire you will then have the ability to move the

assembly without damaging the receiver.

After the black wire has been removed from the dim-12.

mer control board, move the heater assembly with the

rear ame panel farther up into the unit until the panel

clears the receiver on the bottom right panel.

Carefully pull the ame panel up and out of the re-13.

place chassis. Some force will be required when slid-

ing and removing this panel.

Proceed to the correct “Replacement Instructions” in 14.

the following pages for the part in need of repair, (either

heater assembly, remote control receiver, or lower light

harness).

HEATER ASSEMBLY REPLACEMENT

Tools Required: Philips head screwdriver

Wire Cutter

CAUTION: Follow “Preparation for Service” instructions

before proceeding.

With the rear ame panel released, carefully turn the 1.

rear ame panel over and remove the 6 screws that

hold the heater assembly bracket to this panel. (2) on

the left ange, (2) on the right ange, (2) on the bottom

ange. Once heater assembly is free, lay the ame

panel and the heater assembly back down, resting

inside the replace.

Locate the switch housing cover plate to the right of 2.

the heater assembly. Remove the 2 mounting screws

located on the exterior chassis and free the cover plate

from its location.

NOTE: Wires from the thermostat will still be at-

tached so the cover won’t completely come out. You can

just lift and turn it a ¼ turn, then rest it inside the replace

opening.

Remove the 2 heater assembly mounting brackets off 3.

the rear left and the right of the blower motor and fan.

Each bracket has 2 screws securing it to the blower

assembly.

Remove 4 screws on the heat deector panel attached 4.

at the elements and attach it on the same location on

the new heater assembly.

Attach the mounting brackets to the new heater assem-5.

bly in the same location as the original heater.

Remove the wire connections on the original blower 6.

motor; elements; as well as the screw holding the high

limit cutout to the heater. Connect these wires and

screw onto the new heater assembly and back on to

the Heater On/Off switch and remote control receiver in

the same positions as the original connections.

NOTE: Using a at head screwdriver gently pry be-

tween the end of the connector and the heater to release

the wires.

Re-assemble in reverse order as described above7.

LOWER LIGHT HARNESS

REPLACEMENT

Tools Required: Philips head screwdriver

Wire Cutter

CAUTION: Follow “Preparation for Service” instructions

before proceeding.

With the rear ame panel has been released, carefully 1.

turn the rear ame panel over and remove the 4 screws

that hold the heater assembly bracket to this panel.

Once heater assembly is free, lay the ame panel and

the heater assembly back down, resting inside the

replace.

Remove the 3 screws from the rear ame panel that 2.

secure the light harness housing to this back panel.

NOTE: This will allow for better access to the lower

light harness.

Remove the two (2) screws securing the light block as 3.

shown in Figure 6, then remove the light block.

Remove the bulbs by turning them counter clockwise.4.

Remove the screws in each relative terminal on the 5.

terminal block, which secure the blue and white wires

from the light harness.

NOTE: Be sure to note the original conguration of

the wires on the terminal block.

Cut the wire ties that secure the wire harness to the 6.

light harness mounting panel.

From underneath the mounting panel, remove the 7.

small screw in each socket, which secures the sockets

to the panel.

Feed the sockets through the opening on the housing 8.

panel. You may have to rotate the socket slightly to get

them out.

Feed the new sockets into the mounting panel and se-9.

cure with the small screw to the panel. The wires that

connect the two sockets should rest in the ledge, which

is attached to the bottom of the light harness mounting

panel.

Connect the new wire harness into the terminal block 10.

according to the original conguration.

Reassemble in the reverse order as above.11.

UPPER LIGHT HARNESS

REPLACEMENT

Tools required: Phillips head screw driver.

Wire Cutter

WARNING: If the replace was operating prior to ser-

vicing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Unplug (if applicable) or disconnect power

at the circuit breaker before attempting any maintenance to

reduce the risk of electric shock or damage to persons.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 16 17

Kommentare zu diesen Handbüchern

Keine Kommentare

Dimplex VCX1525 Wartungshandbuch Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Dimplex VCX1525