Dimplex VCX1525 Wartungshandbuch PDF herunterladen (Seite 10)

10 www.dimplex.com

Remove the remaining 3 screws holding the center 3.

panel on. (Figure 8)

Taking note of the original location of each wire con-4.

nected to the board, remove each wire and connect

them onto the same location on the new receiver

board.

NOTE: Using a at head screwdriver gently pry be-

tween the end of the connector and the receiver to release

the wires.

Remove the original receiver board off the 4 plastic 5.

mounting tabs on each corner of the receiver. To do

this, squeeze each mounting tab ange/post either by

hand or by or with a pair of needle nose pliers until they

are depressed enough to pull the board off.

Once the original board is free from the tabs, align the 6.

new board over the mounting tabs and gently press the

board onto the tabs.

Re-assemble in reverse order as described above.7.

DIMMER CONTROL BOARD

REPLACEMENT

Tools Required: Philips head screwdriver

Needle Nose Pliers

Remove glass assembly: 1.

Remove the screws securing the glass assembly •

on the bottom of the chassis (Figure 4).

Hold on to the glass assembly with both hands •

and lift the whole assembly straight up to remove

(Figure 5).

Set glass assembly aside in an upright position so •

that the pebbles don’t fall out of the top opening.

Locate the switch housing cover plate (Figure 9). 2.

Remove the 2 mounting screws located on the exterior

chassis and free the cover plate from its location.

NOTE: Wires from the thermostat will still be at-

tached so the cover won’t completely come out. You can

just rest it inside the opening.

Pull the dial off the dimmer controller/potentiometer 3.

located on the switch housing panel.

Remove the nut that secures the potentiometer to the 4.

housing panel.

Replace with the new potentiometer and secure with 5.

the nut from the original one.

With the unit facing up, remove the bottom panel by 6.

removing the screws around the outside of the panel

(11) and the 6 in the middle. (Figure 7)

Gently pull the panel away from the unit and taking 7.

note of the original location, remove each wire and con-

nect them onto the same location on the new control

board.

NOTE: Using a at head screwdriver gently pry

between the end of the connector and the control board to

release the wires.

Remove the original receiver off the 4 plastic mount-8.

ing tabs on each corner of the receiver. To do this,

squeeze each mounting tab ange/post either by hand

or by or with a pair of needle nose pliers until they are

depressed enough to pull the board off. The tabs can

also be cut off and replaced with new ones that come

with the board.

Once the original board is free from the tabs, align the 9.

new board over the mounting tabs and gently press the

board onto the tabs.

Reconnect the wires onto the new board in the same 10.

orientation as the original.

Re-assemble in reverse order as described above.11.

SWITCH REPLACEMENT

3-POSITION SWITCH AND HEATER ON/OFF SWITCH

Tools required: Phillips head screw driver.

NOTE: Your replace has both a 3-Position Switch

as well as a Heater On/Off switch, both of which are

located in the same area on the replace; are similar in

design; and can be replaced in the same way by following

the instructions below.

WARNING: If the replace was operating prior to ser-

vicing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Unplug (if applicable) or disconnect power

at the circuit breaker before attempting any maintenance to

reduce the risk of electric shock or damage to persons.

Remove glass assembly: 1.

Remove the screws securing the glass assembly •

on the bottom of the chassis (Figure 4).

Hold on to the glass assembly with both hands •

and lift the whole assembly straight up to remove

(Figure 5).

Set glass assembly aside in an upright position so •

that the pebbles don’t fall out of the top opening.

Locate the switch housing cover plate. Remove the 2 2.

mounting screws located on the exterior chassis and

free the cover plate from its location.

NOTE: Wires from the thermostat will still be at-

tached; therefore, the cover plate won’t completely come

out. You can just rest it inside the opening.

Locate the switch to be replaced. 3.

Disconnect the wiring connections noting their original 4.

locations.

Depress the retainer clips on 2 sides of the switch and 5.

push the switch out from the casing cover.

Properly orient the new switch and connect all of the 6.

wiring connections according to the original congura-

tion.

Reassemble in the reverse order as above.7.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17

Kommentare zu diesen Handbüchern

Keine Kommentare

Dimplex VCX1525 Wartungshandbuch Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Dimplex VCX1525