Dimplex VCX1525 Wartungshandbuch PDF herunterladen (Seite 7)

PREPARATION FOR SERVICE:

Tools Required: Philips head screwdriver

Wire Cutter

IMPORTANT: Please proceed with the following

steps in preparation for replacement of ONLY the fol-

lowing parts.

Heater Assembly •

Lower Light Harness Assembly •

These preparation instructions do not apply to the

ickermotor;upperlightharness;theswitchesorther-

mostat replacement.

WARNING: If the replace was operating prior to ser-

vicing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

Remove glass assembly: 1.

Remove the screws securing the glass assembly •

on the bottom of the chassis. (Figure 3)

Hold on to the glass assembly with both hands •

and lift the whole assembly straight up to remove.

(Figure 4)

Set glass assembly aside in an upright position so •

that the pebbles don’t fall out of the top opening.

Remove the replace from the wall: 2.

i. Surface Mount: partially loosen the screws from the

keyhole mount openings on the back panel. Loosen

approximately 1/8th of an inch, just enough to lift the

unit off the mounting screws.

NOTE: Take note of which keyholes were used for

mounting so it can be put back into the same position

once service is complete.

ii. Partial Recessed Mount: Remove the 4 wood

screws attached to the back panel, located on top and

bottom of both the left and right side of the unit, releas-

ing it from framed wall opening.

Disconnect power before attempting any maintenance.3.

NOTE: This unit may have been installed to a power

source in one of 2 ways:

Option #1 – Plugged into an outlet: a power cord with •

plug, inserted into an outlet near or behind the re-

place, unplug the replace from the outlet.

Option #2 – Hardwire connection: power supplied from •

electrical wire coming from a dedicated, properly fused

circuit with 120 Volt, 15 Amp rating directly from the

main electrical panel, turn the breaker off at the electri-

cal panel.

It is recommended during original installation, •

there should be an allowance of up to 8 feet of

service cable for connecting power supply to the

junction box on replace.

Hard wire connection can be accessed from inside the

front lower left of the unit if the replace is still mounted

in the wall. If unit has already been dismounted, the

wires can also be accessed from underneath the by

removing the screw from the wire housing cover plate.

Once the replace is removed off of the wall and the 4.

wires from the power source have been disconnected,

lay the replace on a solid surface on its front.

NOTE: If you are laying the unit on a nished surface

that is prone to scratching, be sure to cover the work sur-

face with a protective cover.

Remove the 9 screws to remove the inner back panel 5.

from the outer panel: 4 left, 4 right, 1 lower center of

the back panel. (Figure 6)

Carefully turn the replace over onto it’s back.6.

Remove the 4 screws that attach the ame panel to the 7.

exterior side panel of the replace: 2 on the left and 2

on the right. (Located approx. 6” inches from the bot-

tom).

Remove the 7 screws from the heater assembly cover: 8.

3 on the front of the cover, 2 on the bottom left and 2

on the bottom right of the chassis – (on the left and

right side of the bottom vent). Set the heater assembly

cover aside.

Remove the 4 screws that secure the heater assembly 9.

housing to the bottom of the chassis. The screws are

located above and below the heat vent.

Cut the wire-tie located in the bottom center area of the 10.

light-harness mounting panel, (just above the heater

assembly). This will allow the ame panel to slide up

more freely.

Figure 6

1 2 3 4 5 6 7 8 9 10 11 12 ... 16 17

Kommentare zu diesen Handbüchern

Keine Kommentare

Dimplex VCX1525 Wartungshandbuch Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Dimplex VCX1525