Dimplex CFA36BS Wartungshandbuch PDF herunterladen (Seite 7)

LED

Flicker Motor

Retaining Clip

Circuit Board

and to prevent bodily harm, only use Dimplex replacement

rechargeable batteries.

WARNING: Improper handling of battery may result in

possible explosion hazard, electric shock and severe bodily

injury.

Do not dispose of battery in a re, the battery may •

explode

Do not open or mutilate battery. The battery contains •

chemicals that are toxic to the eyes and skin

To decrease risk of electric shock, remove wrist •

watches and jewelry such as rings and bracelets when

replacing battery.

To decrease risk of electric shock, only use tools with •

insulated handles.

To prevent damage to the electric replace and to •

prevent bodily harm, only replace battery with Dimplex

replacement rechargeable batteries.

To prevent damage to the electric replace and to •

prevent bodily harm, only use Dimplex approved DC

power supply to power and recharge battery.

To dispose of spent battery, return it to place of •

replace purchase, deliver it to a local recycling facility

or ship it to Dimplex North America Limited in the

replacement battery packaging material.

Ensure the replace is turned OFF.1.

Unplug the Power Supply cord from the unit (if at-2.

tached).

Carefully remove the River Rocks (media) from the 3.

Media Tray on the front of the replace

Lift and remove the electric replace from the wall-4.

mounting bracket (Figure 2) and carefully place it

upright on a at surface.

CAUTION: A protective barrier (i.e. blanket) between

the replace and work surface will help prevent scratches

on the work surface or the replace.

On the back of the replace, remove the eight (8) 5.

screws securing the battery cover to the unit, located in

the bottom, right corner of the back panel (Figure 3).

Lift and remove the battery access cover.6.

Tilt the unit backwards, to allow the battery to slide out 7.

of the opening.

NOTE: The battery is heavy so ensure that it will slide

out onto the at surface.

CAUTION: Take care not to damage the 2 wire con-

nections on the left side of the battery. (Figure 3)

Once battery is out of the opening, remove the two (2) 8.

wire lead connectors from the battery terminals taking

note of their original conguration.

NOTE: These wire connectors can be carefully re-

moved one at a time by using needle nosed pliers.

Set the Battery aside.9.

Remove the remainder of the 17 screws which secure 10.

the back panel on to the replace. 3 along the top; 3

along the right (battery side); 5 along the left (switch

side); and 6 on the bottom lip of the back panel.

Lift the back panel off the unit, exposing the internal 11.

components and set it aside.

Looking at the unit from behind, locate the icker motor 12.

on the left beside the circuit board. (Figure 4) Unplug

the motor wire connector from the circuit board and

unhook the wires from the retaining clip(s) on the bot-

tom panel.

Remove the icker motor mounting bracket, by remov-13.

ing the 2 screws that attach to the bottom panel.

Grasp the icker motor with the mounting bracket and 14.

icker rod still attached. Slide the icker rod out of the

icker assembly mounting bracket located on the op-

posite end.

Separate the icker motor and icker rod, by holding 15.

the motor in one hand, grasping the rubber icker con-

nector and rod with the other hand, then twisting and

pulling them apart. Set the icker rod with the rubber

connector aside.

Remove the 2 screws which secure the icker motor to 16.

the motor mounting bracket.

Replace with the new icker motor onto the mounting 17.

bracket and secure the motor to the bracket using the

original 2 screws.

Push the icker rod with rubber connector onto the mo-18.

tor shaft and slide it back into the 2nd icker assembly

mounting bracket.

NOTE: Ensure that the rod has not been bent. If it has

it may cause noises and limited ame effect during usuage.

Secure the mounting bracket to the bottom panel of the 19.

replace with the original 2 screws.

Re-assemble the remainder of the unit in reverse order.20.

NOTE: Before placing the battery back into the open-

ing, reconnect the wires in their original position with black

leading to black and red leading to red to ensure correct

polarity and that they are not pinched when replacing the

access cover.

Figure 4

1 2 3 4 5 6 7 8 9 10 11

Kommentare zu diesen Handbüchern

Keine Kommentare

Dimplex CFA36BS Wartungshandbuch Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Dimplex CFA36BS