Tips for using your appliance.
1. Only pull out the drawer when its time to rell the
water tank or change a lamp, otherwise it may lead to
excess water in the sump and reduced ame eect. If this
happens empty the water from the sump as instructed
under ‘Maintenance’.
2. With the ame setting on minimum the unit will use
approximately 40ml of water per hour and will last 3 times
as long than when it is at maximum ame setting.
3. Do not tilt or move the stove while there is water in the
tank or sump.
4. Make sure that the stove is on a level oor.
5. The ame control knob ‘C’ Fig.2 may be turned up or
down to give a more realistic eect.
6. Sometimes the ames appear more real when the ame
control knob is turned down.
7. Give the ame generator some time to react to
changes you may make on the ame control knob.
8. If condensation occurs on the inside surfaces, reduce
the amount of smoke and ames produced and leave
the doors slightly ajar.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE
Changing lamps.
If a large amount of the smoke appears grey or colourless
it may be that one or more lamps have failed.
You can check for lamp failure as follows.
1. Leaving the ame eect on, open the doors fully, gently
pull the drawer fully out by the tab. (See Fig.3)
2. View the lamps from a distance in front of the stove and
observe which lamp needs to be changed.
3. Put Switch ‘A’ in the ‘OFF’ (0) position, and unplug the
stove from the mains.
4. Leave the appliance for 20 minutes to allow the lamps
to cool down before removing them.
5. Remove the water tank by lifting upwards and place in
a sink.
6. Remove the sump as described in the Cleaning Section.
7. Remove the defective lamp, by gently lifting vertically
and disengaging the pins from the lamp holder, (See Fig.4
and 5). Replace with a Dimplex Opti-myst, 12V, 50W, Gu5.3
base, 8º beam angle, coloured lamp. (Purchased from
www.dimplex.co.uk under the section ‘After Sales Service’,
details of how to purchase the lamps are contained
therein.)
8. Carefully insert the two pins of the new lamp into the
two holes in the lamp holder. Push rmly in place. (See
Fig.4 and 5).
9. Replace the Sump and water tank and carefully close
the drawer and doors.
10. Switch on.
Filling the water tank.
When using the appliance for the rst time or when the
water level warning light comes on, you will hear 2 audible
‘beeps’ when the water is empty and the tank needs
relling, follow these steps.
1. Fully open doors.
2. Press Switch ‘A’ to the ‘OFF’ (0) position (See Fig.2).
3. Gently pull out the drawer as far as possible by the tab.
(See Fig.3)
4. Remove the water tank by lifting upwards and
outwards.
5. Place the water tank in sink and remove cap, Anti-
clockwise to open. (See Fig.6)
6. Fill tank with ltered tap water only. This is necessary
to prolong the life of the ame and smoke producing unit.
The water should be ltered through a conventional
domestic water lter unit and the lter should be replaced
regularly.
7. Screw the cap back on, do not overtighten.
8. Return the tank to the sump, with the tank cap facing
down and the at side of the tank facing outward.
9. Gently push the drawer back in as far as it will go.
10. Press Switch ‘A’ to ‘ON’ ( I ) position (See Fig.2)
11. Press Switch ‘B’ once to turn on ame eect. (See
manual control section and Fig.2)
(12 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern